Closed-Loop 6-DOF Inverse Kinematics Hardware Accelerator — ACE980789

Accelerated Computing Engineering — IP Core Technical Datasheet

Fixed Latency
1,652 cycles (8.260 μs)
Engine Clock
200.0 MHz
Closed-Loop Rate
121.06 kHz
Artix-7 Footprint
5,518 LUTs / 4 DSPs

Overview

The ACE980789 is an ultra-fast, cycle-deterministic hardware accelerator engineered by Accelerated Computing Engineering (ACE) for real-time 6-Degree-of-Freedom (6-DOF) robotic closed-loop Inverse Kinematics (IK). Operating as a production-grade "Math-to-Silicon" architecture, the core transforms non-linear differential kinematics, dynamic $6 \times 6$ geometric Jacobian evaluation, task-space position and angular-twist error regulation, and Damped Least-Squares (DLS) regularized matrix inversion directly into dedicated, pipelined FPGA silicon.

Performing inverse kinematics directly on the FPGA eliminates the communication latency and bus-arbitration jitter encountered when transferring joint feedback and Cartesian setpoints across external buses to an industrial PC (IPC) or host Microprocessor/Microcontroller (MPU/CPU). Solving the entire non-linear kinematic chain within silicon enables execution velocities that are strictly unattainable through conventional software architectures, collapsing iteration latency from hundreds of microseconds down to 8.260 μs on a mid-tier FPGA.

A defining architectural innovation of the ACE980789 is its command-state tracking paradigm: the internal kinematic loop updates and tracks commanded joint angles rather than differentiating raw encoder feedback. Executing a complete iterative pass in $8.260\ \mu\text{s}$ ($1,652$ clock cycles at $200\text{ MHz}$), the physical manipulator displaces by a distance well below the discrete resolution threshold of standard industrial optical encoders within a single cycle. Attempting to differentiate raw encoder feedback over sub-$10\ \mu\text{s}$ intervals would inject severe quantization chatter and discrete noise. By closing the high-bandwidth kinematic integration loop around the commanded state while integrating physical feedback, the ACE980789 achieves continuous sub-micron Cartesian convergence without hunting or limit cycles—even under coarse 12-bit encoder quantization or transient physical actuator stalls—on a 1 m-class reference manipulator.

The core achieves an exceptionally lean resource utilization footprint ($8.70\%$ of Slice LUTs and only $4$ DSP48E1 slices on an entry-level AMD Artix-7 XC7A100T), allowing system integrators to embed real-time 6-DOF kinematics into existing onboard FPGAs without modifying Bill-of-Materials (BOM) costs or requiring board redesigns.

Visit www.accelerated-computing.be for more information.

Key Features

  • Absolute Jitter-Free Determinism: Fixed execution latency of exactly 1,652 clock cycles ($8.260\ \mu\text{s}$ at $200\text{ MHz}$). Execution time is strictly invariant across nominal moves, kinematic singularities, $\pm\pi$ phase-wrap boundaries, and workspace saturation regimes.
  • Extreme Closed-Loop Throughput: Sustains up to 121.06 kHz continuous closed-loop update frequency, enabling direct integration into inner servo current and torque loops.
  • High-Fidelity Golden-Twin Parity: Verified across 22 Hardware-in-the-Loop (HIL) scenarios against a 64-bit floating-point reference model, preserving parts-per-million (ppm) relative task-space accuracy across arbitrary manipulator link scales, exact wrist/elbow/base-axis singularities, and $\pm\pi$ phase-wrap crossings without numerical drift or divergence.
  • Autonomous Quantization & Stall Immunity: Verified under 18-bit ($23.96\ \mu\text{rad}$ LSB), 16-bit with $\pm 3$ LSB oscillating chatter, and coarse 12-bit ($1.53\text{ mrad}$ LSB) discrete encoder feedback—as well as physically stalled encoder states—achieving non-divergent convergence with $0.31\text{–}0.78\ \mu\text{m}$ TCP parity on a 1 m-class reference manipulator.
  • Ultra-Lean Structural Footprint: Consumes only 5,518 Slice LUTs ($8.70\%$), 5,854 Flip-Flops ($4.62\%$), 4 DSP48E1 slices ($1.67\%$), and 1 BRAM tile ($0.74\%$) on an AMD Artix-7 XC7A100T FPGA.
  • Dual-Stage Hybrid Arithmetic: Combines parallel unrolled 2Q30 fixed-point CORDIC joint trigonometry with an IEEE-754 Single-Precision (FP32) floating-point datapath for geometric Jacobian evaluation and unrolled $6 \times 6$ Cholesky matrix inversion.
  • Standard Memory-Mapped Interface & IP Security: Controlled via a dual-port 32-bit BRAM interface (compatible with AMD/Xilinx AXI BRAM Controller or direct RTL state machines) with optional FPGA Silicon DNA node-locked cryptographic licensing.

Theory of Operation

The ACE980789 executes an end-to-end, closed-loop Damped Least-Squares (DLS) differential kinematics solver resolving 6-DOF task-space Cartesian position and angular twist displacements into incremental configuration-space joint adjustments.

1. Commanded Angle Normalization & Parallel CORDIC Trigonometry

Joint angles are represented as signed 32-bit fixed-point numbers in 2Q30 format (1 sign bit, 1 integer guard bit, 30 fractional bits) over the principal normalized interval $[-1.0, +1.0)$ scaled radians (0xC0000000 $= -\pi$ to 0x3FFFFFFF $= +\pi - 1\text{ LSB}$), where $1.0$ scaled radian equals $\pi$ radians. The extra integer guard bit provides a full $[-2.0, +2.0)$ dynamic range (0x80000000 to 0x7FFFFFFF), preventing intermediate saturation during large transient excursions while preserving exact trigonometric periodicity modulo $2.0$ without branching logic. Dedicated unrolled CORDIC primitives evaluate the sine and cosine of all six commanded joints concurrently.

2. Forward Kinematics (FK) and 6-DOF Task-Space Error

Using the analytical manipulator link parameters—shoulder height $D_1$, upper arm length $A_2$, elbow offset $A_3$, forearm length $D_4$, and tool flange offset $D_6$—the forward kinematics pipeline resolves the current commanded Tool Center Point (TCP) Cartesian coordinates $(P_{X,\text{cmd}}, P_{Y,\text{cmd}}, P_{Z,\text{cmd}})$:

$$\begin{aligned} c_{23} &= c_2 c_3 - s_2 s_3, \qquad s_{23} = s_2 c_3 + c_2 s_3 \\ r_w &= A_2 c_2 + A_3 c_{23} + D_4 s_{23}, \qquad z_w = D_1 + A_2 s_2 + A_3 s_{23} - D_4 c_{23} \\ d_r &= D_6 c_4 s_5, \qquad d_t = D_6 s_4 s_5, \qquad d_z = D_6 c_5 \\ r_{\text{total}} &= r_w + c_{23} d_r + s_{23} d_z \end{aligned}$$

$$P_{X,\text{cmd}} = c_1 r_{\text{total}} - s_1 d_t, \qquad P_{Y,\text{cmd}} = s_1 r_{\text{total}} + c_1 d_t, \qquad P_{Z,\text{cmd}} = z_w + s_{23} d_r - c_{23} d_z$$

The 6-dimensional task-space error vector $\mathbf{e} \in \mathbb{R}^{6 \times 1}$ is synthesized by scaling the Cartesian position displacement and angular velocity twist difference against the closed-loop task-space gain $K_{\text{ik}}$:

$$\mathbf{e}_{[0..2]} = K_{\text{ik}} \left( \mathbf{P}_{\text{target}} - \mathbf{P}_{\text{cmd}} \right), \qquad \mathbf{e}_{[3..5]} = K_{\text{ik}} \left( \boldsymbol{\omega}_{\text{target}} - \boldsymbol{\omega}_{\text{curr}} \right)$$

3. Analytical Geometric Jacobian & DLS Normal Matrix

The core evaluates the full $6 \times 6$ analytical geometric Jacobian matrix $\mathbf{J}(\mathbf{q})$ concurrently in IEEE-754 single precision. To invert the kinematic mapping cleanly across singular configurations—including wrist singularities ($q_5 = 0$), full arm radial extensions, and overhead shoulder-axis traversals—the core synthesizes the symmetric $6 \times 6$ normal matrix $\mathbf{H}$ with scalar Levenberg-Marquardt damping $\lambda^2$:

$$\mathbf{H} = \mathbf{J}\mathbf{J}^T + \lambda^2 \mathbf{I}$$

4. Cholesky Factorization & Autonomous Accumulator Update

The regularized matrix $\mathbf{H}$ is factored into a lower-triangular matrix $\mathbf{L}$ such that $\mathbf{L}\mathbf{L}^T = \mathbf{H}$, followed by sequential forward substitution ($\mathbf{L}\mathbf{y} = \mathbf{e}$), backward substitution ($\mathbf{L}^T\mathbf{z} = \mathbf{y}$), and configuration-space back-projection:

$$\Delta\mathbf{q} = \mathbf{J}^T \mathbf{z}, \qquad \mathbf{q}_{\text{next}} = \text{wrap}_{[-1, +1)}\big(\mathbf{q}_{\text{cmd}} + \Delta\mathbf{q}\big)$$

Because the Jacobian and error scaling are formulated directly in scaled radians, $\Delta\mathbf{q}$ is produced directly in scaled radians and latched into the 2Q30 commanded joint registers without software division.

Recommended Operating Envelope & Integration Guidelines

Parameter / Input Recommended Operating Range Engineering Rationale
Closed-Loop Gain (KIK) 0.100 to 0.250 Provides overdamped to critically damped discrete convergence in 6–26 cycles; values $\ge 0.300$ approach discrete-time gain overshoot on large steps.
DLS Damping (LAMBDA_SQ) $2.0 \times 10^{-5}$ to $1.0 \times 10^{-3}$ ($1.0 \times 10^{-4}$ nominal) Maintains FP32 Cholesky positive-definiteness across exact wrist, elbow, and overhead singularities without excessive steady-state lag.
Setpoint Step Rate Interpolated ($\le 5\text{ mm/cycle}$) At $121.06\text{ kHz}$, $5\text{ mm/cycle}$ corresponds to $> 600\text{ m/s}$ Cartesian velocity—far exceeding physical manipulators while keeping per-cycle $|\Delta q| < 0.5$ scaled rad.
Initial Seed Angles (Q_CMD_FX) $[-1.0, +1.0)$ scaled rad (0xC0000000..0x3FFFFFFF) Principal $[-\pi, +\pi)$ interval; internal 2Q30 accumulator seamlessly handles transient excursions into $[-2.0, +2.0)$ during $\pm\pi$ wrap crossings.

Hardware Resource Utilization & Timing Closure

Post-implementation resource utilization and timing closure metrics below are extracted directly from the routed AMD Vivado implementation targeting the AMD Artix-7 XC7A100T FPGA (xc7a100tcsg324-1), isolating the standalone ACE980789 core from evaluation testbench logic:

Resource Primitive ACE980789 Used XC7A100T Available Utilization (%)
Slice LUTs (Total)5,51863,4008.70%
  • LUT as Logic5,41963,4008.55%
  • LUT as Memory (Distributed RAM / SRL)9919,0000.52%
Slice Registers (Flip-Flops)5,854126,8004.62%
Occupied Slices1,65315,85010.43%
Block RAM (RAMB36 / 36Kb Tiles)1.0135.00.74%
DSP48E1 Slices42401.67%
F7 / F8 Multiplexers228 / 4031,700 / 15,8500.72% / 0.25%
  • Core Engine Clock (clk_fast): $200.0\text{ MHz}$ nominal ($5.00\text{ ns}$ period), closed with WNS = +0.267 ns and WHS = +0.034 ns (0 failing endpoints across 11,897 routed endpoints under worst-case -1 commercial process corners).
  • Host Interface Clock (clk_user): Decoupled dual-port BRAM clock domain supporting $50\text{ MHz}$ to $160+\text{ MHz}$ AXI interconnects or direct RTL state machines.
  • Deterministic Pipeline Latency: Verified via on-chip AXI GPIO hardware cycle counters across all 22 verification scenarios at exactly 1,652 clock cycles ($8.260\ \mu\text{s}$) with 0 cycles jitter.

Memory-Mapped Register Interface (32-Bit Dual-Port BRAM)

Host communication is handled through a 32-bit True Dual-Port Block RAM (depth: 1,024 words). Port A connects to the user/host bus, while Port B connects directly to the internal kinematic engine.

Word Addr Register Name Dir Format Functional Description
0START_CMDIN/OUTU32 FlagWrite 0x1 to trigger computation pass; hardware clears to 0x0 at Cycle 1652.
1 .. 5D1, A2, A3, D4, D6INFLOAT32Manipulator kinematic link lengths and joint offsets (meters).
6LAMBDA_SQINFLOAT32Levenberg-Marquardt damping factor $\lambda^2$ for DLS singularity regularization.
7KIKINFLOAT32Closed-loop task-space tracking integration gain.
8 .. 22RESERVEDINFLOAT32Reserved for feedforward gravity/PD torque options (initialize to 0.0).
23 .. 28Q_ACT_FX[0..5]IN2Q30Measured joint encoder feedback angles (scaled radians, $1.0 = \pi$).
29 .. 34Q_CMD_FX[0..5]IN/OUT2Q30Commanded joint state vector; updated autonomously in-place at Cycle 1652.
35 .. 37TARGET_P[X,Y,Z]INFLOAT32Desired TCP Cartesian position setpoints $[X, Y, Z]$ (meters).
38 .. 40TARGET_W[X,Y,Z]INFLOAT32Desired tool angular velocity twist vector $[\omega_x, \omega_y, \omega_z]$ ($\text{rad/s}$).
41 .. 43W_CURR[X,Y,Z]INFLOAT32Current estimated tool angular velocity twist vector ($\text{rad/s}$).
70 .. 72PX, PY, PZ_CMDOUTFLOAT32Real-time forward kinematics TCP Cartesian coordinates (meters).
73 .. 78e[0..5]OUTFLOAT32Scaled 6-DOF task-space error vector (diagnostic telemetry).
150 .. 155DQ[0..5]OUTFLOAT32Calculated configuration-space joint velocity increments ($\Delta q$ in scaled rad).
156 .. 161NEXT_Q_CMD[0..5]OUT2Q30Autonomous next commanded joint state vector for servo drive injection.

Comprehensive Hardware-in-the-Loop (HIL) & Edge-Case Verification

The ACE980789 silicon implementation on the AMD Artix-7 XC7A100T was validated against a 22-scenario automated HIL verification suite spanning nine distinct operational and stress domains. Both the FPGA accelerator and the independent double-precision software golden twin (AceIkTwin) maintained autonomous closed-loop state accumulators across every multi-step run.

Protocol, Lockstep & 6-DOF Twist Verification Summary

  • Host Link & Dual-Port BRAM Bit Integrity: Passed 100% of read/write walking-bit and pattern tests (0x00000000, 0xFFFFFFFF, 0xA5A55A5A, 0x3FC00000).
  • Mode A Cycle-by-Cycle Lockstep Parity (LOCK-A): Maximum TCP discrepancy bounded at $1.37\ \mu\text{m}$ and maximum joint increment discrepancy at $25.28\ \mu\text{rad}$ across 20 consecutive steps.
  • 6-DOF Angular Twist Excitation Audit (TWIST-01): With simultaneous non-zero TARGET_W and W_CURR inputs, the hardware task-space error vector e[0..5] matched the double-precision model to $9.92 \times 10^{-8}$ and joint velocity increments matched within $20.04\ \mu\text{rad}$.
  • Cycle-Level Latency & Jitter Audit: Every single execution pass across all 22 scenarios completed in exactly 1,652 clock cycles ($8.260\ \mu\text{s}$ @ $200\text{ MHz}$) with 0 cycles jitter.

Complete 20-Scenario Closed-Loop Edge-Case Results

Test ID Domain Scenario & Stress Condition Conv. Step Final TCP Parity Max $|\Delta q|$ Latency
NOM-01NominalNominal Vertical Step ($+20\text{ mm}$ in Z, $K_{\text{ik}}=0.200$, $\lambda^2=10^{-4}$)Step 0130.31 μm0.40951,652 cyc
NOM-02NominalCompound 3D Move from Alternate Seed Posture BStep 0111.64 μm0.42861,652 cyc
NOM-03NominalZero-Error Stationary Hold (Target == Initial FK)Step 0000.57 μm0.00001,652 cyc
SING-01SingularityExact Wrist Singularity ($q_5 = 0.0\text{ rad}$, collinear axes 4 & 6)Step 1550.70 μm0.01091,652 cyc
SING-02SingularityNear-Wrist Singularity Perturbation ($q_5 = 10^{-4}$ scaled rad)Step 0590.72 μm0.03651,652 cyc
SING-03SingularityFull Radial Arm Extension / Elbow Boundary SingularityStep 0061.06 μm0.08881,652 cyc
SING-04SingularityOverhead Base-Axis Singularity Traversal (Near Z-Axis)Step 0311.12 μm0.00121,652 cyc
WRAP-01Phase-Wrap2Q30 $\pm\pi$ Boundary Rollover ($+0.999 \rightarrow -0.999$ scaled rad)Step 0081.19 μm0.13641,652 cyc
WRAP-02Phase-WrapExact 2Q30 Extremes ($-1.0$ and $+0.999999999$ scaled rad)Step 0060.77 μm0.01171,652 cyc
WRAP-03Phase-WrapBack-Hemisphere ($-X$) Base Yaw Crossing $\pm\pi$ BoundaryStep 0070.88 μm0.05921,652 cyc
SAT-01SaturationOut-of-Reach Workspace Saturation ($2.5\text{ m}$ Goal @ $5\text{ mm/step}$)Bounded14.15 μm0.30771,652 cyc
SAT-02SaturationBoundary-Grazing Unreachable Target ($1.05\text{ m}$ Envelope)Bounded4.71 μm0.03341,652 cyc
ENC-01Encoder StressCoarse 12-Bit Encoder Quantization ($1.53\text{ mrad}$ LSB Floor)Step 0120.78 μm0.37891,652 cyc
ENC-02Encoder Stress16-Bit Encoder with $\pm 3$ LSB Oscillating Measurement NoiseStep 0130.75 μm0.39551,652 cyc
ENC-03Encoder StressStalled Physical Plant (Frozen Q_ACT_FX vs Command Loop)Step 0130.31 μm0.40951,652 cyc
NUM-01NumericalLow DLS Regularization Conditioning ($\lambda^2 = 2.0 \times 10^{-5}$)Step 0164.35 μm0.41911,652 cyc
NUM-02NumericalHigh-Gain Operating Envelope Upper Limit ($K_{\text{ik}} = 0.250$)Step 0130.53 μm0.46911,652 cyc
GEO-01GeometryDegenerate Spherical Wrist & Zero Offset ($A_3=0.0, D_6=0.0$)Step 0601.05 μm0.01141,652 cyc
GEO-02GeometryMicro-Manipulator Link Scale ($80\text{ mm}$ Links, $5\text{ mm}$ Step)Step 0160.08 μm0.08271,652 cyc
TRAJ-01Trajectory4-Corner Square Box + Sudden Step Reversal (5 Waypoints)Step 1671.60 μm0.06171,652 cyc

Software Golden Twin Reference Implementation

To support offline verification, trajectory pre-planning, and Hardware-in-the-Loop regression testing, ACE delivers the Python reference twin class (AceIkTwin) alongside the exhaustive 22-scenario HIL validation testbench:

import math
import numpy as np

class AceIkTwin:
    """Bit-accurate software golden twin for the ACE980789 6-DOF IK accelerator.
    Angles are expressed in scaled radians [-1.0, +1.0), where 1.0 = pi rad.
    """
    def __init__(self, D1: float, A2: float, A3: float, D4: float, D6: float,
                 lambda_sq: float = 0.0001, Kik: float = 0.200):
        self.D1, self.A2, self.A3 = float(D1), float(A2), float(A3)
        self.D4, self.D6 = float(D4), float(D6)
        self.lambda_sq = float(lambda_sq)
        self.Kik = float(Kik)

    @staticmethod
    def wrap_to_scaled_pi(scaled_rad: float) -> float:
        """Wraps an angle strictly to [-1.0, +1.0) scaled radians."""
        return ((scaled_rad + 1.0) % 2.0) - 1.0

    @staticmethod
    def scaled_rad_to_2q30(scaled_rad: float) -> int:
        """Encodes scaled radians [-1.0, +1.0) into signed 32-bit 2Q30 format."""
        wrapped = ((scaled_rad + 1.0) % 2.0) - 1.0
        raw = int(round(wrapped * (1 << 30)))
        raw = max(-(1 << 31), min((1 << 31) - 1, raw))
        return raw & 0xFFFFFFFF

    @staticmethod
    def u32_to_scaled_rad(u_val: int) -> float:
        """Decodes signed 32-bit 2Q30 register value into scaled radians."""
        signed = u_val - (1 << 32) if (u_val & (1 << 31)) else u_val
        return float(signed) / float(1 << 30)

    def forward_kinematics(self, q_cmd_scaled: list[float]) -> tuple[float, float, float]:
        """Computes Cartesian TCP position (PX, PY, PZ) in meters."""
        q_rad = [self.wrap_to_scaled_pi(float(x)) * math.pi for x in q_cmd_scaled]
        s1, s2, s3, s4, s5, s6 = [math.sin(qi) for qi in q_rad]
        c1, c2, c3, c4, c5, c6 = [math.cos(qi) for qi in q_rad]

        c23 = (c2 * c3) - (s2 * s3)
        s23 = (s2 * c3) + (c2 * s3)
        rw = (self.A2 * c2) + (self.A3 * c23) + (self.D4 * s23)
        zw = self.D1 + (self.A2 * s2) + (self.A3 * s23) - (self.D4 * c23)
        dr, dt, dz = self.D6 * c4 * s5, self.D6 * s4 * s5, self.D6 * c5
        r_total = rw + (c23 * dr) + (s23 * dz)

        PX_cmd = (c1 * r_total) - (s1 * dt)
        PY_cmd = (s1 * r_total) + (c1 * dt)
        PZ_cmd = zw + (s23 * dr) - (c23 * dz)
        return PX_cmd, PY_cmd, PZ_cmd

    def step(self, q_cmd_scaled: list[float], target_pos: list[float],
             target_w: list[float] = None, w_curr: list[float] = None) -> dict:
        """Executes one deterministic DLS pipeline pass mirroring the FPGA RTL."""
        target_w = [0.0, 0.0, 0.0] if target_w is None else target_w
        w_curr = [0.0, 0.0, 0.0] if w_curr is None else w_curr

        # 1. Joint trigonometry & Forward Kinematics
        q_rad = [self.wrap_to_scaled_pi(float(x)) * math.pi for x in q_cmd_scaled]
        s1, s2, s3, s4, s5, s6 = [math.sin(qi) for qi in q_rad]
        c1, c2, c3, c4, c5, c6 = [math.cos(qi) for qi in q_rad]

        c23 = (c2 * c3) - (s2 * s3)
        s23 = (s2 * c3) + (c2 * s3)
        rw = (self.A2 * c2) + (self.A3 * c23) + (self.D4 * s23)
        zw = self.D1 + (self.A2 * s2) + (self.A3 * s23) - (self.D4 * c23)
        dr, dt, dz = self.D6 * c4 * s5, self.D6 * s4 * s5, self.D6 * c5
        r_total = rw + (c23 * dr) + (s23 * dz)

        PX_cmd = (c1 * r_total) - (s1 * dt)
        PY_cmd = (s1 * r_total) + (c1 * dt)
        PZ_cmd = zw + (s23 * dr) - (c23 * dz)

        # 2. Task-space position & angular twist error
        e = np.array([
            self.Kik * (target_pos[0] - PX_cmd),
            self.Kik * (target_pos[1] - PY_cmd),
            self.Kik * (target_pos[2] - PZ_cmd),
            self.Kik * (target_w[0] - w_curr[0]),
            self.Kik * (target_w[1] - w_curr[1]),
            self.Kik * (target_w[2] - w_curr[2]),
        ], dtype=np.float32)

        # 3. 6-DOF analytical geometric Jacobian
        diff_p = (-s23 * dr) + (c23 * dz)
        diff_v = (c23 * dr) + (s23 * dz)
        J = np.zeros((6, 6), dtype=np.float32)
        J[0, 0] = -PY_cmd; J[1, 0] = PX_cmd; J[5, 0] = 1.0
        J[0, 1] = c1 * ((-self.A2 * s2) - (self.A3 * s23) + (self.D4 * c23) + diff_p)
        J[1, 1] = s1 * ((-self.A2 * s2) - (self.A3 * s23) + (self.D4 * c23) + diff_p)
        J[2, 1] = (self.A2 * c2) + (self.A3 * c23) - (self.D4 * s23) + diff_v
        J[3, 1] = s1; J[4, 1] = -c1
        J[0, 2] = c1 * ((-self.A3 * s23) + (self.D4 * c23) + diff_p)
        J[1, 2] = s1 * ((-self.A3 * s23) + (self.D4 * c23) + diff_p)
        J[2, 2] = (self.A3 * c23) - (self.D4 * s23) + diff_v
        J[3, 2] = s1; J[4, 2] = -c1
        J[0, 3] = (-s1 * dr) - (c1 * c23 * dt)
        J[1, 3] = (c1 * dr) - (s1 * c23 * dt)
        J[2, 3] = -s23 * dt; J[3, 3] = c1 * c23; J[4, 3] = s1 * c23; J[5, 3] = s23
        J[0, 4] = c1 * ((c23 * c4 * c5 * self.D6) - (s23 * s5 * self.D6)) - (s1 * s4 * c5 * self.D6)
        J[1, 4] = s1 * ((c23 * c4 * c5 * self.D6) - (s23 * s5 * self.D6)) + (c1 * s4 * c5 * self.D6)
        J[2, 4] = (s23 * c4 * c5 * self.D6) + (c23 * s5 * self.D6)
        J[3, 4] = (s1 * s4) - (c1 * s23 * c4); J[4, 4] = (-c1 * s4) - (s1 * s23 * c4); J[5, 4] = c23 * c4
        wrist_u = (c23 * c5) + (s23 * c4 * s5)
        wrist_v = s4 * s5
        J[3, 5] = (c1 * wrist_u) - (s1 * wrist_v)
        J[4, 5] = (s1 * wrist_u) + (c1 * wrist_v)
        J[5, 5] = (s23 * c5) - (c23 * c4 * s5)

        # 4. Damped Least-Squares Cholesky solve & 2Q30 accumulator update
        H = J @ J.T + self.lambda_sq * np.eye(6, dtype=np.float32)
        L = np.linalg.cholesky(H)
        z = np.linalg.solve(L.T, np.linalg.solve(L, e))
        dq = J.T @ z

        raw_next = [self.wrap_to_scaled_pi(q_cmd_scaled[i] + float(dq[i])) for i in range(6)]
        next_q = [self.u32_to_scaled_rad(self.scaled_rad_to_2q30(raw_next[i])) for i in range(6)]
        return {
            'PX_cmd': PX_cmd,
            'PY_cmd': PY_cmd,
            'PZ_cmd': PZ_cmd,
            'e': e,
            'dq': dq,
            'next_q_cmd_scaled': next_q,
        }

Architectural Customization & Licensing

While the ACE980789 is delivered as a turnkey, production-verified IP core, Accelerated Computing Engineering's "Math-to-Silicon" methodology enables rapid bespoke adaptations:

  • Kinematic Topology & DOF Customization: Adaptable to SCARA, Delta, 7-DOF redundant manipulators, or custom non-standard Denavit-Hartenberg (DH) kinematic chains.
  • Direct RTL / Streaming Interfaces & Joint Clamping: Configurable with standalone RAM interfaces for zero-CPU EtherCAT/PROFINET IRT and FOC motor-drive integration, plus optional per-cycle $\Delta q$ saturation clamps.
  • Multi-Arm Memory Partitioning: Partitioned BRAM address spaces allow a single time-shared ACE980789 engine to govern coordinated multi-arm cobot cells with minimal logic growth.
  • Dynamic Friction & Gravity Torque Compensation: Seamless pairing with a Neural ACE core configured for non-linear Stribeck friction feedforward torque compensation (see ACE910N01).
  • Multi-Vendor FPGA Fabric Porting: Portable across AMD UltraScale+, Intel/Altera Cyclone and Agilex, Microchip PolarFire, and Lattice Avant devices.

Deliverables

The ACE980789 is supplied as a synthesis-ready, encrypted netlist Vivado IP core compatible with the AMD Vivado IP Catalog. Each licensed package includes:

  1. Production netlist Vivado IP core with RTL simulation wrappers.
  2. Bit-accurate Python software golden twin package (ace_ik_twin.py).
  3. 22-scenario automated Hardware-in-the-Loop (HIL) and edge-case testbench suite.
  4. Complete AMD Vivado example block design and hardware integration guide.
  5. Optional FPGA Silicon DNA node-locked cryptographic licensing keys.

For licensing inquiries, evaluation bitstreams, and custom core engineering, contact engineering@accelerated-computing.be or visit www.accelerated-computing.be.

Data Privacy note: By contacting us via email, you agree that we will use your provided contact details and mathematical specifications solely to evaluate project feasibility during our early-access phase. We do not sell or share your personal information with third parties. We may use standard web analytics tools to monitor basic, aggregated website traffic to improve our site performance.